Lw Continuous Horizontal Decanter Centrifuge for Sludge Dewatering

• Customization: Available
• Warranty: 12monthes
• Type: Centrifuge
• Model NO.: LW
• Object: Liquid Solid Separation
• Separation Mode: Filter Type
• Operating Type: Continuous Type
• Installation: Horizontal
• Centrifuge Type: Horizontal Spiral Centrifuge
• Pressure: Medium Pressure
• Condition: New
• Material: SS304 or SS316 L
• Motor: ABB
• Touch Screen: Siemens
• Inverter: ABB
• Transport Package: Wooden Cases
• Specification: 2065*1050*800
• Trademark: SHENZHOU
• Origin: China
• HS Code: 8421192000
• Production Capacity: 500sets
• Package Size: 130.00cm * 145.00cm * 135.00cm
• Package Gross Weight: 1050.000kg

Product Description

Product Description of shenzhou decanter centrifuge

This equipment is a LW series product, commonly used for dehydration and concentration. Widely used for maximum dewatering requirements of municipal and industrial wastewater sludge. It is characterized by small size, high rotational speed, and small processing capacity, and is used in situations where large separation factors and small processing capacity are required. According to practical use, it can be divided into: clarification type, dehydration type, concentration type, separation type, classification type, extraction type; Users can choose by themselves. Dehydration horizontal spiral centrifuge is suitable for easily separated materials with large particle size, large solid-liquid density difference, low viscosity, high concentration, strong processing capacity, and higher dryness than clarity. Materials such as sludge or wastewater containing fine particles usually require the addition of flocculants to condense the fine particles into large particles, which are then dewatered using a sedimentation centrifuge.

 

 

The horizontal screw centrifuge relies on the density difference between the solid and liquid phases to accelerate the sedimentation rate of solid particles under the action of centrifugal force to achieve solid liquid separation. The centrifuge consists of two rotors, one called a drum, and the other rotor is a screw discharger (referred to as a screw). When the drum rotates at a high speed, the slurry inside the drum rotates with the drum and is subjected to a centrifugal force that is many times greater than gravity. In this way, solid particles will be separated from the liquid and settle onto the inner wall of the drum from the centrifuge drum shaft. The screw discharger located inside the drum rotates at a speed lower than the drum and pushes the deposited solid particles to the slag outlet, The differential rotational speed between the outer drum and the screw discharger depends on the transmission ratio of the differential and its rotational speed.

 

 

This liquid clarifying device adopts horizontal design which balances the layout of electric motor and bowl. As a result, outstanding operation stability generates minimized vibration.

 

Dual electric motor control enables stepless speed adjustment on bowl and spiral components.

 

Scroll conveyor flight inside this continuous centrifuge is painted by abrasion resistant alloy or welded by hard alloy. Moreover, main components on our horizontal decanter centrifuge, such as rotating bowl and spiral parts, are made from corrosion resistant stainless steel or dual-phase steel, whereby offering exceptional speed limits and separation ratio.

 

Our mud dewatering equipment comes with three options including cycloidal gear, planetary gear and hydraulic differential, resulting in large rang of differential adjustment. Therefore, this industrial centrifuge can be applible to diverse solids.

 

Multiple protections are available on our horizontal decanter centrifuge to ensure operation safety, including over-vibratation protection, bearing temperature detection, screw conveyor torque protection rotating and differential speed detection, as well as nitrogen-filled explosion-proof protection, motr overload and over heat protection.

 

JG type rubber shock absorber requires no anchor bolts.

 

 

1. The large content of solid will speed up the wearing of the centrifuge parts touching sludge. To solve this problem, Shenzhou adopts the tungsten carbide material at the wearing parts like screw blade, solids discharge port and sludge distribution port. This kind of protection will extend the services life of the machine.

2. The power consumption is an issue of great concern to users. For better pushing out the solid cake, the decanter centrifuge need to be equipped with motors that with sufficient torque. To reduce the power consumption during the running of the decanter, Shenzhou designed 2 units driving motors as common DC bus mode, which makes the back motor a generator during normal running condition. 

 

Shenzhou equipped VFD control panel to the dewatering decanter centrifuge. According to different sludge condition and treatment target, the user can set up the running speed and differential speed of the machine. All setting can be done on the HMI touch screen. By adding the temperature and vibration sensor and installing the signal receiving device in the control panel. The VFD panel can display the running condition and monitor the machine. In the VFP control panel, SZ normally installs VFD and other electrical components for feeding pump control.

In the sludge dewatering package, the decanter centrifuge is the core equipment, while it is always equipped with sludge feeding pump, polymer dosing unit and solid cake screw conveyor to make an integrated package.

 

 

According to user's requirement, the product contact parts can be made of austenite stainless (321, 316L….), Haynes alloy, titanic alloy or other anti-erosion materials.

 

 

Model	Diameter	Length	Max Speed (R/Min)	L/D Ratio	G-Force (G)	Capacity	Main Motor Power	Weight	Dimension (L*W*H)
	(Mm)	(Mm)				(M3/H)	(Kw)	(Kg)	(Mm)
LW450*1350	450	1350	3000	3	2268	4-20	30	2000	2870*1700*1130
LW450*1800	450	1800	2800	4	1976	4-25	37	2500	3320*1700*1130
LW500*1250	500	1250	2800	2.5	2195	5~25	37	2500	2770*1800*1170
LW500*1500	500	1500	2800	3	2195	5~30	37	2680	3020*1800*1170
LW500*2000	500	2000	2500	4	1750	5-35	45	4000	3520*1800*1170
LW530*1855	530	1855	2600	3.5	2006	5-38	55	4680	3885*1350*1600
LW530*2120	530	2120	2400	4	1709	5-40	55	4800	4150*1350*1600
LW550*1855	550	1855	2600	3.5	2006	5-35	55	2680	3885*1350*1600
LW550*2120	550	2120	2400	4	1709	5-40	55	4000	4150*1350*1600
LW650*1950	650	1950	2200	3	1761	6-45	75	5000	4840*1510*1720
LW650*2600	650	2600	2000	4	1456	6-65	90	6000	5490-1510*1720
LW720*2160	720	2160	2000	3	1612	7-80	120	6000	5200*1600*1800
LW720*2880	720	2880	2000	4	1306	7-90	120	8000	3100*1600*1800
LW760*2280	760	2280	2200	3	2060	10-90	110	10000	4892*1950*1610
LW760*3040	760	3040	2000	4	1702	10-120	132	12500	5652*1950*1610
LW800*2400	800	2400	1800	3	1451	20-100	150	12000	5820*2000*1300

 

Spiral conveyor

The spiral feeder is made of 304 stainless steel, and the forging process is adopted , which can enhance its corrosion resistance.

BD structure, spraying hard alloy powder on the surface of the blade. The thickness is over 3mm .The spiral outlet is equipped

with a replacement hard alloy sleeve, which greatly prolongs the service life of the machine blade. Because of this technology,the maintenance cost of the machine is greatly reduced. Other parts in contact with the material are 304 stainless steel.

 

Drum of shenzhou decanter centrifuge 

The drum is cast by 304 stainless steel in centrifugal casting, the forging process is adopted , which can enhance its corrosion resistance, The replaceable alloy sleeve is installed in the solid state outlet, so that the mother material of the drum's outlet is not worn, and the wear-resistant bar is installed in the drum to make the drum inside not worn.

 

PLC Control Panel of shenzhou decanter centrifuge

The electrical control adopts the double conversion auto control system, which can display the parameters such as frequency, rotation speed, differential speed and current of operating major and auxiliary electrical engine.
Eletrical Components: SIEMENS/Schneider/ABB

 

 

The equipment has the characteristics of continuous feeding and discharging. The chemical separation equipment has been applied to two-phase (solid liquid) and three-phase (solid liquid liquid) slurry separation in chemical, pharmaceutical, environmental protection, mining, food and other industries. The various materials listed below are only partially used, and various new uses are increasing. For specific materials, it is necessary to pass tests or analogies to determine the type and technical parameters of the corresponding centrifuge. Chemical, petroleum, food, pharmaceutical, kitchen oil and water residue, magnetic particle treatment, sewage treatment plants, pharmaceutical plants, food plants, laboratories, petroleum industry, new energy industry, biotechnology, chemical fiber, polymeric materials, leather manufacturing, cosmetics, printing and dyeing plants, knitting plants, environmental protection technology, and so on.

Chemical industry: polyethylene, polystyrene, fumaric acid, urea, ammonium sulfate, potassium nitrate, polyamide, caprolactam, sodium carbonate, compound fertilizers, sodium chloride, traditional Chinese medicine, sodium sulfite, bile alum, PVC, ferrite, polypropylene glycol, activated carbon, various resins, etc.

Food: Citric acid, tartaric acid, sodium glutamate, amino acids, salt, granulated sugar, xylitol, corn fiber, saccharin, flax, coffee, etc.

Mining industry: iron sulfate, copper sulfate, nickel sulfate, amine thiocyanate, etc.

Industrial and municipal wastewater treatment

Oil and gas drilling mud/drilling fluid control

Washing, Separation, and Dehydration of Starch

Isolation of Antibiotics from Mycelia and Fermentation Broth

Dehydration of Soybean and Wheat Protein

Dehydration of fish meal and meat

Dehydration of distiller's grains.

Clarification and Extraction of Fruit Juice

Isolation and purification of animal and vegetable oils

Production and purification of olive oil, palm oil, and avocado oil

Separation and purification of coal tar

Classification of kaolin and graphite

Grading and dehydration of dyes and pigments

Clean coal foam flotation and slime dewatering

Working principle of mineral classification and dehydration

 

 

The larger the solid particles in the material, the easier it is to separate. The size of the solid particles varies, and the final separation effect is determined by the small particle solid phase. This machine can generally remove solid particles above 5 um. When the solid particles are especially small, they will not settle and separate out, but will be discharged together with the clarified liquid; The final separation effect depends on the distribution of solid particles in the material. The more particles above 5 um, the better the separation effect; On the contrary, the separation effect is worse.

 

Generally, crystalline solids and fibrous solids are easier to separate, while flocs and paste solids are more difficult to separate. Due to the large maximum water solubility of flocs and paste solids, when spirally pushing sediment, it is easy to slip and affect the separation effect, so the flow rate should not be too large when separating flocs and paste solids.

 

The greater the weight difference between the solid phase and the liquid phase, the better the separation, and vice versa, the worse the separation effect The lower the liquid viscosity, the easier it is to separate. When the liquid viscosity is higher, the solids entrained in the clarified liquid increase, and the separation effect becomes worse. At this time, the material temperature can be increased and the viscosity can be reduced to improve the separation effect (the maximum feed temperature is not greater than 95 ºC).

 

 

From a separation perspective, the smaller the feed flow rate, the smaller the axial flow rate of the material in the drum, the longer the residence time of the material in the drum, and the better the separation effect. As the feed volume increases, the axial flow rate increases, and the retention time of the material in the drum decreases. The separation effect becomes worse.

 

The feed volume of the centrifuge is also limited by the maximum slag removal capacity of the spiral. If the feed volume is too large, the separated sediment will not be discharged in a timely manner, resulting in blockage of the drum.

 

Therefore, when using the centrifuge, the appropriate feed flow rate should be selected based on the material characteristics, separation requirements, and the solid content of the material, Generally, when the solid content is large, the feed rate should not be too large. The appropriate feed rate can be determined after comparing the separation effects of various flows. Generally, it is recommended that the flow rate should not be too large for materials that are difficult to separate, and the flow rate for materials that are easy to separate can be larger. However, attention should be paid to the maximum slag discharge amount of the spiral, otherwise it will cause material blockage

 

To better ensure the safety of your goods, professional, environmentally friendly, convenient and efficient shipping packaging services will be provided.

 

 

 

 

- Technical direction when installation, debugging

- Training for operation and maintain worker

 

 

Q1.What's your advantage? Why we choose you?
A:1) More than 50 years experience of centrifuge & separator production and R&D.We have the most professional techniques and team. More advantage in price
2)Great production capacity Sustainable Supply . According to customer requirements, We support the customized include package.
3)We use famouse good quality materials and the best production process

Q2.What's the Payment?
A:T/T would be better with quick transfer and few bank fees. LC could also be accept, but the
procedure is complex and the fee is high. You can also use Western Union and Paypal.

Q3.Are you a factory or trading company?
A:We are a professional manufacturer. We are warmly welcome clients from worldwide to visit our factory and cooperate with us.

Q4.How long is the warranty period ?
A:12 months.

 

Hot Tags: industrial large capacity centrifuge, China industrial large capacity centrifuge manufacturers, suppliers, factory, Porcelain clay waste treatment equipment, Potassium chloride treatment equipment, centrifuge for the fermentation industry, large volume centrifuge, Large sediment separator, Industrial Large Capacity Centrifuge